Uncategorized
Showing 1921–1935 of 1964 results
- Uncategorized
Water Bath, Rectangular, Electric
Double walled, inner chamber of stainless steel, outer made of stove enamelled mild steel. Top has 75 mm holes with concentric rings. Temperature range upto 100°C, accuracy ±1°C, Heater fitted with automatic cut-out device, thermostat, two indicator lights, mains switch. Works on 220-240V, 50 Hz.
SKU: CH10123 - Uncategorized
Water Bath, Serological
Double walled, inner chamber of stainless steel, outer made of stove enamelled mild steel, with insulation in between, Thermostatic temperature control from 5°C above room temperature to 95°C with accuracy ±0.5°C. Bath has a stainless steel dome cover, perforated and removable shelves, drain plug, two indicator lights, thermostat control knob , heater with automatic cut-out. Works on 220-240 V, 50 Hz. With connector plug and 1 metre of 3 core cable. Supplied without racks.
SKU: CH10124 - Uncategorized
Water Still
Easy to use, safe to operate and is designed for trouble free continues operation. Suitable for general laboratory use.
Features:
The still produces 4 litres/hr of distilled water through a 3 kW heater housed in a horizontal borosilicate glass boiler.Boiler & Condenser: Are made of heat resistant borosilicate glass and are designed for high efficiency, boiler is with PTFE stopcock for easy cleaning. All plumbing connection are through screw thread connectors.
Stand: Powder coated for long rust free life.
Heater: 3 KW chromium plated heater fitted with a thermostat.
Output: Approx 4 ltrs/ Hrs.SKU: CH14030 - Uncategorized
Water Still, Wall Type
Automatic electrically heated. Designed to provide pyrogen free distilled water at low cost. All main parts like boiling chamber, lid, baffle, condenser tube are of stainless still .The heating element has automatic cut- out which cuts current off if water level falls. Easy to clean and reassemble. Complete with wall mounting bracket, electrical cord, connector etc. To work on 240V, 50 Hz
SKU: CH14020 - Uncategorized
Water Taps, Swan Neck
Inlet tail is threaded 1/2 in. BSP, The outlet brass tube is coupled to the tap standard by means of a sleeve nut allowing the neck to swivel or to be locked in any desired direction, leakproof operation, designed for pressures upto 80 psi finished in hard chrome plating.
SKU: CH11200 - Uncategorized
Westminister Electromagnetic Kit
A very effective and motivating learning aid in elementary electromagnetism. Consists of 8 anisotropic alloy magnets, 8 ceramic ferrite magnets, 4 steel magnet yokes, 6 plotting compasses, 4 hardboard formers to take compasses, 1 bottle iron filings 250 gm, 4 dispensers for iron filings , 4 double C-cores, 4 clips for C cores, 4 Aluminium rings, 4 Aluminium split rings, 4 armatures with axle tubes, 4 Aluminium axle rods, 8 split pins, 16 rivets, 4 formers for coils, 4 reels cello tape, 4 reels copper wire, 4 sheets white pasteboard, 4 plain postcards, 4 reels white cotton thread, 1 length latex rubber tubing, 4 each resistors 100 ohms and 10 ohms, 4 support bases, 10 MES bulbs, 8 MES bulb holders,1 wood clamp and 1 wooden block. With instructions.
SKU: PH50160 - Uncategorized
Wheatstone Bridge, Four Gap
Four gap systems, enabling two additional resistances to be interpolated in the additional gaps, enable greater accuracy of measurement by reducing unwanted resistance to a minimum. Two brass strips are provided to close the gaps when so required. Complete with jockey.
SKU: PH50404